Renseignements généraux

Nº de série

21187

Nº de partie

1

Nombre total de parties

3

Ou

S/O

Brevets

S/O

Description générale

METAL FRAME/ ENAMELLED METAL BODY/ METAL HOT SHOE WITH SYNTHETIC TEMP. CONTROL DIAL/ METAL ROLL WITH FIBRE PADDING, FABRIC COVER & CARDBOARD CASING/ SYNTHETIC LATCH KNOB/ RUBBER COVERED CORD/ RUBBER PLUG WITH BRASS PRONGS.

Dimensions

Remarque : Cette information reflète la taille générale pour l’entreposage et ne représente pas nécessairement les véritables dimensions de l’objet.

Longueur

42,5 cm

Largeur

43,0 cm

Hauteur

78,2 cm

Épaisseur

S/O

Poids

S/O

Diamètre

S/O

Volume

S/O

Lexique

Groupe

Technologie domestique

Catégorie

Buanderie

Sous-catégorie

S/O

Fabricant

Ou

Thor

Pays

Canada

État/province

Ontario

Ville

Toronto

Contexte

Pays

Inconnu

État/province

Inconnu

Période

Inconnu

Canada

Inconnu

Fonction

Inconnu

Technique

Inconnu

Notes sur la région

Inconnu

Détails

Marques

MFR'S PLATE READS: 'MODEL No 300/ SERIAL NO. 21187/ VOLTS 115 CYCLES 60 WATTS 1320/ CSA APPROVAL NO. 719/ THOR CANADIAN CO. LTD./ TORONTO CANADA'/ DECALS READ: 'Thor/ AUTOMAGIC/ GLADIRON/ TRADE MARKS REG. U.S. PAT. OFF.', 'MANUFACTURED UNDER/ CANADIAN LETTERS PATENT/ PATENTED 1944-1945/ RD-1941- RENEWED 1946' & 'MADE IN CANADA'/ TEMP. CONTROL DIAL READS: 'OFF RAYON SILK WOOL COTTON LINEN' WITH NOS. FROM 1 TO 25 BELOW/ 'RELEASE' INCISED ON HOT SHOE LEVER/ Markings on cardboard cylinder which fits over roll read: ‘Thor/ AUTOMATIC/ TRADE MARK/ GLADIRON/ IRON A SHIRT/ IN 4 ½ MINUTES/ AUTOMAGICALLY/ TURN ROLL/ AND SEE HOW/ Operates with a single knee lever/ Folds to closest size and tucks away/ The Gladiron turns out perfectly ironed shirts in minutes because/ the patented Gladiron roll slips INSIDE the sleeves - Tricky pieces/ like shirts, pyjamas, puffed sleeve dresses are no trick to iron with a/ Gladiron...you just slip them over the roll (no other ironer has one/ like it) and guide them through. And you do it sitting down...using/ a single knee lever from start to finish!/ Place shirt in position on the roll/ like this - Put your left arm through the/ left sleeve of the shirt (label side/ should be towards you) and draw it over/ the roll. Continue drawing shirt to the/ right until the right sleeve is well over the roll and left sleeve and/ body of shirt hang loosely over roll support housing at the extreme right./ TO IRON - move knee/ lever to right as far as it will/ go and release it./ TO STOP - again move/ knee lever to right as far as/ it will go and release it./ TO PRESS - move knee lever half way to/ the right and hold it in this position with your/ knee. This stops the roll without raising the shoe./ 1 PLACE SHIRT IN POSITION ON ROLL AND IRON FIRST SLEEVE/ Place the sirt on the roll (as shown at left)/ so roll is inside the right sleeve and the seam/ where the cuff joins the sleeve lines up with/ left end of roll./ Smooth sleeve on roll so that underarm/ seam will be at the back of the roll./ 2 IRON SHOULDER AND BACK OF YOKE/ Move shirt to left until collar band lines up/ with right end of roll. Iron down to first but-/ ton. Now centre unironed portion of yoke and/ adjust roll to start six or seven inches below/ back of collar. Iron to collar seam and stop. Raise shoe and move shirt to left until left/ shoulder in lined up with right end of roll./ Iron over shoulder to first button-hole. Now/ place the second sleeve in position and iron/ exactly as you did the first sleeve./ 3 IRONING THE REST OF YOUR SHIRT IS SIMPLY FLATWORK/ Centre the back of the shirt on the roll and/ iron from tail to ironed portion of yoke./ Take shirt by collar and draw it toward/ you to again bring tail to starting point./ Move shirt to left and iron up button-hole/ side to armhole. Adjust to avoid armhole and/ iron to first button-hole. Turn shirt over and/ iron button side of front the same way but/ with buttons cushioned against roll./ Iron cuffs around the left end of roll, first/ on the wrong side, then on the right side./ Iron collar centred on roll (the long way)/ first on the wrong side, then on the facing side./ Fold collar down and press to set fold.'/ Metal plate on back of body reads: ‘CAUTION/ FOR USE ONLY ON WALL/ OR BASE RECEPTACLE./ DO NOT USE THIS MACHINE/ IN ANY DAMP LOCATION/ OR NEAR WATER PIPES/ OR OTHER GROUNDED/ METAL.'

Manque

From CA of 09/06/1994 by Tony Missio: No - Complete

Fini

FRAME METAL PAINTED BLACK/ BODY METAL WITH WHITE (DISCOLOURED)ENAMELLED FINISH/ HOT SHOE INTERIOR METAL UNFINISHED & POLISHED, EXTERIOR METAL PAINTED BLACK/ TEMP. CONTROL DIAL BLACK SYNTHETIC WITH WHITE PRINTING/ ROLL COVER BEIGE FABRIC/ LATCH KNOB BLACK SYNTHETIC/ CORD COVERING & PLUG BLACK SYNTHETIC

Décoration

DECAL ON FRONT INCLUDES WING ON EITHER SIDE OF MODEL NAME 'THOR'/ DECAL ON BACK CONTAINS MAPLE LEAF AT CENTRE