Renseignements généraux

Nº de série

737 (dewar)

Nº de partie

1

Nombre total de parties

1

Ou

S/O

Brevets

S/O

Description générale

non-ferrous metals/ aluminum telescope interface adaptor/ synthetic handles & parts

Dimensions

Remarque : Cette information reflète la taille générale pour l’entreposage et ne représente pas nécessairement les véritables dimensions de l’objet.

Longueur

30,0 cm

Largeur

27,0 cm

Hauteur

48,0 cm

Épaisseur

S/O

Poids

S/O

Diamètre

S/O

Volume

S/O

Lexique

Groupe

Photographie

Catégorie

Appareils-photos

Sous-catégorie

S/O

Fabricant

Ou

Inconnu

Pays

United States of America

État/province

Inconnu

Ville

Inconnu

Contexte

Pays

Canada

État/province

Nouvelle-Écosse

Période

early 1980s+

Canada

This is the camera built by SMU under a NSERC funded project to develop a CCD camera for use on telescopes. In 1979 (ck) SMU astronomers Dr. Gary Welch and Dr. David Dupuy (moved to Virginia Military Institute in 1982) were awarded a grant of $150,000 to develop one of three systems (UBC and Laval were the other departments awarded grants to develop CCD cameras). The use of CCDs in cameras provided, among other things, a more efficient way to do photometry of stars or nebula, image objects from planets to galaxies, or as detectors on spectrographs, etc. It revolutionized astronomy in less than 10 years allowing space telescopes like Hubble and planetary probes like Mars Rover to surpass others using traditional imaging technology by hundreds of times in sensitivity. The gold annodized section (the dewar) held the liquid nitrogen to cool the CCD chip and the aluminum section held the chip, filters and acted at the interface to the telescope and computer. The silver piece on the dewar was the temperature sensor and the objective was to keep the CCD at -140 C =/- 2 or 3 degress. The interface was designed by R.C. Brooks and manufactured by Coldwell Enterprises of Dartmouth, NS. The Dewar was built in the US.

Fonction

A device attached to a telescope as part of a telescope camera system to take photographs of astronomical phenomena.

Technique

The challenges in developing a CCD camera included overcoming the following: cooling the CCD to a constant low temperature (-140 C -- with liquid N2) to decrease the dark current (current generated by the chip when powered up but without any light falling on the chip), developing software to read off, store and manipulate the large volume of data generated, etc. The dewar was purchased off the shelf from a US source. This holds the N2 and provides a cold finger that comes into contact with the pack of the CCD to cool it in order to decrease the dark current and allow the faint signal to be read off with less noise. The dewar envelop was evacuated to decrease the heat loss. One charge of N2 would last during a nights observing. Vacuum was normally in the range of 10-4 to 10-5 Torr. The interface was designed by R. Brooks (then of Saint Mary's University, now Curator of Physical Sciences at CSTM.), and made by Colwell Enterprises of Dartmouth, NS. Connections to power the CCD and to read off the data were provided through this interface. The equipment was used and tested on the 16" Cassegrain reflector of the Burke-Gaffney Obs. at Saint Mary's and also at the 41" (ck?) At Lowell Obs. in Tuscon, Arizonia. In operation the N2 would be added and vacuum would be established by connecting the dewar to a Sargeant-Welsh hi-vac vacuum pump via a 2" dia. heavy walled hose. Once the vacuum was established, the connection would be sealed and the hose removed since one did not want the vibrating hose to be connected while observing.

Notes sur la région

Inconnu

Détails

Marques

Incised lettering on dewar reads "737"/ cast lettering on vacuum hose connection flange reads "VACOA/ BOHEMIA, N.Y./ MODEL 5D50"/ black lettering on vacuum gauge reads " VT [LOGO]/ varian/ TYPE 0531/ tc vacuum gauge"/ red plastic labels for jacks read "video" & "temp"

Manque

appears complete

Fini

Gold anodized dewar/ black & colourless synthetic parts/ unfinished metallic & plated parts

Décoration

S/O